RFMW, Ltd. announces design and sales support for the API Weinschel 4209 series of digital attenuators. Interfacing with popular, high frequency test equipment, the 4209-31.5-1 is equipped with 2.92mm Female connectors while the 4209-31.5-2 offers 2.4mm Female connectors. Both the 4209-31.5-1 and 4209-31.5-2 provide 31.5dB of attenuation range in 0.5dB steps and operate from 100MHz to 40GHz. MMIC technology offers repeatable performance for uninterrupted RF when changing attenuation values. These units can be controlled using parallel (TTL compatible), I2C, SPI, UART, or USB interfaces making them ideal for ATE systems simulating RF fading for 2G/3G/4G LTE and 5G in MIMO,…
Author: RFMW
RFMW, Ltd. announces availability of a white paper from Dielectric Laboratories (DLI). “Choosing blocking capacitors – it’s more than just values” outlines how designers often use rules-of-thumb or approximate equations linking capacitor values to final RF performance. DLI takes a real world look at performance that can’t be predicted by design theory, and then analyzes common capacitor bypass networks to compare actual measurements against theoretical performance.
RFMW, Ltd. announces design and sales support for thin film, fixed attenuator pads from SemiGen, Inc. SemiGen offers a series of fixed attenuators from 1 to 30dB in 1dB increments with flat frequency response from DC to 50GHz. The SFAP series feature precise resistor films and superior metallization resulting in consistent performance and reliability. Full side wraps connect the topside ground to the backside metallization for surface mount or on-board installation. Gold bondable top side contacts for the input and output make these ideal for standard RF/microwave assembly techniques. Power handling is 1 to 5 Watts CW. Return loss is…
RFMW, Ltd. announces design and sales support for an ultra-broad bandwidth, GaN, solid state power amplifier from Aethercomm. Model number SSPA 0.2-2.5-200 operates from 200 to 2500MHz and delivers a typical, saturated output power of 200 Watts. Designed and tested to withstand MIL-STD-810 high shock and vibration requirements, small signal gain is ~60dB and operating voltage is 50 Volts DC. The SSPA 0.2-2.5-200 is offered in a modular housing that is approximately 5”(width) by 9”(long) by 1.5”(height). The RF input connector is SMA female and the RF output connector is Type N female.
RFMW, Ltd. announces design and sales support for a high-performance, X-band, T/R module. Designed for next-generation AESA radar applications, the Qorvo QPM1002 incorporates a T/R switch, low noise amplifier and power amplifier in a 5x5mm QFN package for tight spacing requirements. The QPM1002 performs well in high temperature environments due to 0.25um GaN-on-SiC fabrication. Saturated, pulsed output power from the transmit amplifier is 35dBm with small signal gain of 33dB. Noise figure on the receive side is 2.2dB with small signal gain of 25dB. Input power survivability is up to 2W without permanent damage, compared with a typical GaAs LNA,…
RFMW, Ltd. announces design and sales support for a family of high-performance Front-End Modules (FEMs) designed for improved range in Low-Power WAN (LPWAN), IoT applications. The Skyworks Solutions SKY66420, SKY66423 and SKY66421 support designs in the 860 to 930MHz frequency range. The SKY66420, SKY66423 are fully featured FEMs that include a power amplifier, Low-Noise Amplifier and T/R switch. The SKY66421 is a power amplifier. All 3 devices are pin-to-pin compatible and provide transmit power up to 27dBm while drawing 280mA from a 2.0 to 4.8V supply. Receive gain for the full-featured FEMs is 18dB with Noise Figure of 1.5dB. Increased…
RFMW, Ltd. announces design and sales support for a Silicon on Insulator (SOI) single-pole, six throw (SP6T) switch designed for use in CATV, satellite set top, and other high-performance communications systems. Qorvo’s QPC6762 operates in 75 ohm environments from 5 to 2000MHz and offers 34dB of mid-band isolation. Low insertion loss of 0.4dB and IIP3 of 75dBm highlight exceptional performance for CATV and FTTH system developers. The QPC6762 is offered in a 2 x 2mm, low-cost, QFN package.
RFMW, Ltd. announces design and sales support for a 7-bit digital attenuator from Integrated Device Technology, Inc. (IDT). The F1958 features ultra linear IIP3 of 64dBm with 31.75dB of control range in 0.25dB steps. IDT offers this DSA for 3G, 4G and 4G+ base stations, Distributed Antenna Systems, Remote Radio Heads and other applications within its 1 to 6000MHz frequency range. Glitch-Free technology minimizes transient switching overshoot to protect power amplifiers or ADC during transitions between attenuation states. Settling time is ~1.2uSec utilizing serial or parallel control interfaces. Operating from a 3.3 or 5V supply, the F1958 is housed in…
RFMW, Ltd. announces design and sales support for a 2.4GHz Wi-Fi FEM. Qorvo’s QPF7221 front end module integrates a receive coexistence BAW filter with a 2.4GHz Power Amplifier, SPDT switch, and LNA with bypass capability. The filter provides >40dB of isolation from adjacent LTE bands. Rx gain is up to 13.5dB while Tx gain is 34dB. Designed for 5V operation, module performance is optimized versus a discrete lineup for reduced BOM costs and increased reliability. The QPF7221 is offered in a 3.0×4.5 mm package.
RFMW, Ltd. will highlight new products and technologies at the European Microwave Week 2018 Exhibition to be held at Ifema Feria de Madrid, Spain September 25th to 27th. Located in Booth 139, RFMW Europe will provide product demonstrations and information on high power transistors and amplifiers, MMIC amplifiers, board level switches, attenuators, terminations, filters and other RF components important to design engineers. In addition, RFMW Europe will offer T&M accessories and RF cable assemblies for design and production test environments. Sales engineers and application specialists will be on hand to support specific project questions and component design considerations. RFMW, it’s…